Chulio rašė:Remis7 rašė:..............................
3.slapuku, signa, immo yra? nėra
Tokiu atveju siulyciau patikrinti ar viskas gerai sujungta, ar yra/sveiki sito paleidimo modulio saugikliai, pasikeisti pulto baterija. Po to ishsistudijuok manuala, bandyk nustatyti reikiamus seting'us, paleisti testus. Jei pavyksta, pabandyk paleisti is naujo. Jei nepavyksta greiciausiai tavo sitai irangai out...
(+12V) saugiklis ok, jį išėmus ir vėl įstačius On/Off Control Switch (raudonas LED) šviečia 2-4 sek. ir užgęsta.... bet jis turi pagal mane šviesti visuomet raudonai arba žaliai, priklausomai nuo būsenos.
pačiame modulyje nemačiau daugiau saugiklių. įtariu kad kažkas yra nusimušę... pultelis vizualai veikia (led'aiš šviečia)
na reiks dar kartą viską pereiti ir patikrinti.
neina nei programuoti
Programming An Option:
If you want the factory setting, DO NOTHING and skip this section. If
you want to change one or more of the features, then continue with
the following procedures:
1. Open the hood.
2. Turn the ignition ON (do not start the vehicle).
3. Press and HOLD the brake pedal.
4. Quickly press and release the programming button once.
5. Release the brake pedal.
6. The control LED will flash Red 1 time (signaling that you are now
in the Option Programming mode).
7. The LED color reflects the first option (Green LED is for Factory
setting, Red LED is for Optional setting). Pressing the brake pedal
advances to the next option. By continuing to push the brake
pedal, the user will advance through all of the options and then
start back at Option #1 again.
8. After pushing the brake pedal, the LED flashes Red (the # of the
option) before turning Red or Green, reflecting the state of the
option (Green for factory setting, Red for Optional setting). Push
the programming button to change from the factory setting to
the option setting and vice versa.
9. If no options are selected or changed after 6 seconds the unit
will automatically exit programming.
10. Push the control switch so the LED is Red. The unit is now ready.
11. Turn off the ignition.
arba
2) Code Learning
Your transmitter is factory coded to the remote starter module with
over 16,000,000 different codes. The remote starter module can
learn the codes of up to 4 different transmitters. If you want to add
additional transmitters to the receiver or if it does not respond to
your transmitter - follow the steps below to teach the receiver the
transmitter code(s):
A. Open Hood.
B. Turn the ignition ON (do not start the vehicle).
C. Press and HOLD brake pedal.
D. Quickly push and release Programming button twice.
E. Release the brake.
F. The LED will glow solid Orange.
G. Hold down the LIGHTS button on the transmitter for a second
until you hear the horn honk (or just look for the orange LED to
go out for half a second). The module has now learned the transmitter
code. Release the transmitter button.
H. To learn additional transmitters (up to 3 more), within a few
seconds, push the LIGHTS button on another transmitter for a
second or more until you hear the horn honk (or see the orange
LED go out for half a second). Repeat for the remaining transmitters.
I. 5 seconds after the last time the transmitter was learned the unit
exits the code-learning stage. (The Red LED light will turn on
solid when unit exits Code learning).
J. Turn off the ignition.
Note: Teaching the module a new transmitter code will erase all previous
codes - so all transmitters must be taught. You have only 5
seconds between transmitters to begin teaching a new transmitter.
Remis7 » 03 Sau 2011, 19:42 
